收藏本站
AL8806
Application Information
AL8806 Operation
In normal operation, when voltage is applied at V IN , the AL8806 internal switch is turned on. Current starts to flow through sense resistor R SET ,
inductor L1, and the LEDs. The current ramps up linearly, and the ramp rate is determined by the input voltage V IN and the inductor L1.
DFLS230LH
D1
R SET
12V
0R082
Multi-
die
C1
C2
AL8806
C3
LED
GND
4.7μF 100nF
1μF
33μH
L1
Figure 1 Typical Application Circuit
This rising current produces a voltage ramp across R SET . The internal circuit of the AL8806 senses the voltage across R SET and applies a
proportional voltage to the input of the internal comparator.
When this voltage reaches an internally set upper threshold, the internal switch is turned off. The inductor current continues to flow through R SET ,
L1, the LEDs and the schottky diode D1, and back to the supply rail, but it decays, with the rate of decay determined by the forward voltage drop of
the LEDs and the schottky diode.
This decaying current produces a falling voltage at R 1 , which is sensed by the AL8806. A voltage proportional to the sense voltage across R SET is
applied at the input of the internal comparator. When this voltage falls to the internally set lower threshold, the internal switch is turned on again.
This switch-on-and-off cycle continues to provide the average LED current set by the sense resistor R SET .
LED Current Control
The LED current is controlled by the resistor R SET in Figure 1.
Connected between V IN and SET the nominal average output current in the LED(s) is defined as:
I LED ?
V THD
R SET
If the CTRL pin is driven by an external voltage (higher than 0.4V and lower than 2.5V), the average LED current is:
I LED ?
V CTRL V THD
V REF R SET
For example for a desired LED current of 1.33A and a default voltage V CTRL =2.5V the resulting resistor is:
R SET ?
V THD V CTRL
I LED V REF
?
0 . 1 2 . 5
1 . 33 2 . 5
? 75 m ?
DC Dimming
The CTRL pin can be driven by an external DC voltage (V CTRL ), to adjust the output current to a value below the nominal average value defined by
R SET . The LED current decreases linearly with the CTRL voltage when 0.5V ≤ V CTRL ≤ 2.5V, as shown on page 4 for 4 different current levels.
Note that 100% brightness setting corresponds to V CTRL = V REF , nominally 2.5V. For any voltage applied on the CTRL pin that is higher than V REF ,
the device will not overdrive the LED current and will still set the current according to the equation V CTRL = V REF .
When the CTRL voltage falls below the threshold, 0.4V, the output switch is turned off which allows PWM dimming.
AL8806
Document number: DS35144 Rev. 5 - 2
7 of 15
www.diodes.com
July 2013
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AL8807W5-7 IC LED DRVR DCDC BUCK SOT25
AL9910AS-13 IC LED DRVR HIGH BRIGHT SO8EP
ALC60481R05 PWR SUP AC-DC 6-48V 1.05A 50.4W
ALV100362R5 POWER SUPPLY AC-DC 36V 2.5A 90W
ALV60361R7 POWER SUPPLY AC-DC 36V 1.7A 61W
ALV80126R5 POWER SUPPLY AC-DC 12V 6.5A 78W
AOZ1083CI IC LED DRVR BUCK CC 1.2A SOT23-6
AOZ1935QI IC LED DRVR WHITE BCKLGT 16QFN
相关代理商/技术参数
AL8806QMP-13 功能描述:LED 驱动器 IC 1 输出 DC DC 稳压器 降压（降压） 模拟，PWM 调光 1.5A（开关） 8-MSOP-EP 制造商:diodes incorporated 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:有效 类型:DC DC 稳压器 拓扑:降压（降压） 内部开关:是 输出数:1 电压 - 供电（最低）:6V 电压 -?供电（最高）:30V 电压 - 输出:36V 电流 - 输出/通道:1.5A（开关） 频率:1MHz 调光:模拟，PWM 应用:汽车级 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸焊盘 供应商器件封装:8-MSOP-EP 标准包装:1
AL8807 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:HIGH EFFICIENCY LOW EMI 36V 1A BUCK LED DRIVER
AL8807A 制造商:未知厂家 制造商全称:未知厂家 功能描述:The AL8807A is a step-down DC/DC converter designed to drive LEDs with a constant current
AL8807AEV1 功能描述:AL8807A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:680mA 输出和类型:1，非隔离 电压 - 输出:- 特性:可调光 电压 - 输入:6 V ~ 36 V 所含物品:板 使用的 IC/零件:AL8807A 标准包装:1
AL8807AEV3 功能描述:AL8807A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:1A 输出和类型:1，非隔离 电压 - 输出:- 特性:可调光 电压 - 输入:6 V ~ 36 V 所含物品:板 使用的 IC/零件:AL8807A 标准包装:1
AL8807AMP-13 功能描述:LED照明驱动器 High EFF DIMM 36V 1A / 1.3A Buck LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
AL8807AW5-7 功能描述:LED照明驱动器 High EFF Low EMI 36V 1A Buck LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
AL8807BMP-13 功能描述:LED 驱动器 IC 1 输出 DC DC 稳压器 降压（降压） PWM 调光 1.3A（开关） 8-MSOP-EP 制造商:diodes incorporated 系列:- 包装:带卷（TR） 零件状态:有效 类型:DC DC 稳压器 拓扑:降压（降压） 内部开关:是 输出数:1 电压 - 供电（最低）:6V 电压 -?供电（最高）:36V 电压 - 输出:40V 电流 - 输出/通道:1.3A（开关） 频率:1MHz 调光:PWM 应用:- 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸焊盘 供应商器件封装:8-MSOP-EP 标准包装:2,500